1. 中科聚峰礦井車設備

        • 服務熱線:

          15065707252

        當前位置:首頁 > 新聞中心 > 常見問題 >

        新聞中心

        服務熱線電話

        15065707252

        裝載機出現故障的解決措施

        來源:http://www.socialsecurityutah.com/ 發布時間:2022-04-06 瀏覽次數:200

        內容詳情:
        因為井下裝載機工作環境比較差,在使用過程中,一定要多加注意,正確的操作方法以及日常維護保養都是保證井下裝載機可以正常工作的前提,當然,井下裝載機使用時間久了,質量再好的設備,也不能完全避免一點不出故障,下面我們來談一下井下裝載機常見故障及解決方法!
        Because the working environment of the underground loader is relatively poor, we must pay more attention in the process of use. Correct operation methods and daily maintenance are the premise to ensure that the underground loader can work normally. Of course, the underground loader has been used for a long time, and no matter how good the equipment is, it can not completely avoid failure. Let's talk about the common faults and solutions of the underground loader!
        井下裝載機出現故障的解決措施
        Solutions to faults of underground loader
        井下裝載機驅動橋殼內潤滑油不足,主、從動螺旋傘齒輪嚙合空隙太小,差速器殼與十字軸行星齒輪空隙太大。加滿潤滑油按標準,調節其空隙達到正常值。
        The lubricating oil in the drive axle housing of the underground loader is insufficient, the meshing gap between the driving and driven spiral bevel gears is too small, and the gap between the differential housing and the spider planetary gear is too large. Fill up the lubricating oil and adjust the clearance to the normal value according to the standard.
        井下裝載機轉向泵進油濾清器或輸油管阻塞,轉彎轉向柱與轉向器連接處空隙小或無空隙,轉向器閥芯與閥套、定子與轉子配合過緊單穩閥或溢流調工作壓力偏低或卡死,轉向泵容量效率低。這時應該清潔過濾芯或拆換輸油管,調節其空隙,拆換轉向器或清潔碾磨,調節其工作壓力達到標準值,拆換油泵。
        The oil inlet filter or oil delivery pipe of the steering pump of the underground loader is blocked, the gap between the steering column and the steering gear is small or no gap, the cooperation between the valve core and the valve sleeve, the stator and the rotor of the steering gear is too tight, the working pressure of the monostable valve or overflow regulator is low or stuck, and the capacity efficiency of the steering pump is low. At this time, clean the filter element or remove and replace the oil delivery pipe, adjust its gap, remove and replace the steering gear or clean the grinding, adjust its working pressure to reach the standard value, and remove and replace the oil pump.
        如果井下裝載機輪邊固錐滾子軸承出現毀壞,行星輪軸滾針軸承毀壞,太陽輪及行星輪斷齒毀壞,內齒圈出現打齒,內齒圈與內齒圈支承架連接螺栓斷。應當及時拆換軸承、調節其空隙,更換滾針軸承,更換行星輪以及太陽輪,拆換內齒圈,拆換其螺栓。
        If the fixed tapered roller bearing at the wheel edge of the underground loader is damaged, the needle roller bearing of the planetary axle is damaged, the teeth of the sun gear and planetary gear are broken, the teeth of the inner gear ring are broken, and the connecting bolts between the inner gear ring and the inner gear ring support frame are broken. The bearing shall be replaced in time, the gap shall be adjusted, the needle roller bearing shall be replaced, the planetary gear and sun gear shall be replaced, the inner gear ring shall be replaced, and its bolts shall be replaced.
        以上就是為大家介紹的有關井下裝載機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服務http://www.socialsecurityutah.com
        The above is the detailed introduction of the underground loader. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.socialsecurityutah.com
        久久精品国产2020观看福利